Cavity Wall Insulation Cost Duncanville

Is it time for Roof Insulation Installation in Duncanville? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.

Sheet Insulation

One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.

Sound Deadening Insulation

When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.

Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.

Almost all Roof Insulation Installation in Duncanville are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.

Insulation Blanket

Spray Foam Insulation Basics

There is a trend in the construction industry toward the use of spray foam insulation as opposed to the traditional pink roll batt or even cellulose varieties. With fuel costs rising all the time, it is becoming more important all the time to recognize and incorporate this important advancement in energy conservation and human comfort.

The second law of thermodynamics states that heat will always flow in one direction only, and that it will always flow from warm to cold. What that means to a home owner is that heat is always going to try to escape from the warm house to the cold outside, and that is why houses require insulation. One of the problems with traditional pink roll insulation is that it is installed and then stays in one place. Houses do actually move ­ they settle and shift and expand and contract over time and are then not exactly the same as they were when they were built. Spray foam insulation expands and contracts with the structure, so the insulation seal is never broken.

Spray foam insulation costs far more than the traditional pink roll insulation or cellulose insulation; it is about triple the cost. However, statistics from over a year ago claim that spray foam insulation will save a home owner thirty nine percent on heating and cooling costs. Given what has happened to fuel costs in the last year, the thirty nine percent could turn out to be a very large amount of money.

Acoustic Insulation

Icynene Insulation

 If you are one of the millions of homeowners in the United States or in Canada that have recently discovered your house is suffering from mold in your attic, and are looking for solid answers, I know it can be extremely confusing.

There are as many companies out there promoting their products, as there are offering their services to correct the mold and clean it up. It can be extremely bewildering and if you haven't discovered it already, I am sure you will. There are many reasons for this. First there are no national guidelines that are required to be followed if you have a mold problem.  Secondly the ones that do exist, are incomplete and many times contradict one another!

This article will help you sort out the BS (that's baloney stuff folks) specifically the BS technique of dry ice blasting and shall also help you to find a contractor that will actually solve your problem.

A little background about mold in attics. Mold in attics is primarily caused by improper ventilation. In the northern climates this is often due to heat loss in the winter months when the hot air escaping from the house condenses against the cold boards of the attic, and is sometimes exacerbated by an improperly discharged bathroom fan. In the south it can be caused by an improperly functioning HVAC unit located into the attic letting cold air escape and condense against the hot boards of the attic or by an improperly discharged bathroom fan or dryer vent. In both climates what happens is moisture becomes trapped in the attic areas and accumulates on the boards of the attic sheathing and rafters, where mold starts to grow.

Four things are required for mold to grow. One: a spore must be present, which is like a mold seed (hint there are spores in virtually every breath you have ever taken this means they are very abundant but nearly invisible, 10,000 of them can fit on the head of a pin). Two: a food source  must be present, this is something which was once alive or is still alive, preferably to the mold something that is cellulose based (hint this is any plant based organic matter like the boards in your attic and the rafters, even the paper backing on the rolled  insulation can be a food source, not to mention the paper on the backside of the ceiling drywall under the insulation); Three: the right temperature mold must be present, molds have a narrow temperature range in which they thrive; usually between 20 and 100 degrees Fahrenheit with the majority living between 40 degrees and 90 degrees ; Fourth:and lastly, water must be present (hint  you can stir all of the above three things in a pot and mold  will not grow without water, water is essential to mold growth but may be present as vapour only, not necessarily as a liquid).

Problem Solved Right?? Wrong!

Well, whats wrong you ask? Plenty! First the spores are lofted into the air where they become invisible to the naked eye, many times these spores are left floating, and when the contractor removes his equipment with the problem looking solved, they remain lurking and floating; just waiting to land and recontaminate the structure!

But the most important reason it is ineffective, has to do with the way mold grows. Remember how we talked about the dandelion roots? Well the ice blasting does a great job at removing the pigment from the mold.  This is in the surface layer with the fruit bodies. What it doesn't do is to remove the roots!

Now don't get me wrong it is completely possible to ice blast away enough wood to remove the roots . But in order to accomplish this the contractor has to grind away at the wood till 1/2 inch has been removed! Remember most attics are only 1/2 inch thick plywood in the first place!  Additionally, if the rafters are blasted away 1/2 inch around all three exposed side your roof is likely to collapse!  This process is just another one of the many gimmicks that have been tried to charge high prices and to stand out in the marketplace.

That's why we developed a completely safe time tested non toxic to people process that completely eliminates mold without destroying the structure and leaving your house mold free permanently! Remember to hire a contractor whose system was designed with eliminating the roots of the mold problem not just the stains the mold makes! Save money don't pay to have your mold fixed twice! Don't use dry ice blasting!


Roof Insulation Cost Texas