Roof Insulation Cost Texas

Installing Home Insulation Cost Texas to your home, attics or outer walls may not be a typical do it yourself weekend project but it certainly can be one that can save time, money and energy costs if done correctly.

Spray On Insulation

Learn how and when it is appropriate to consider expanding foam insulation as a do it yourself project and when you might be better off with a professional doing the installation or even considering other foam insulation alternatives.

Roll Insulation

Well it need not in fact you may be able to think outside the box as it were and combine systems to come up with a Home Insulation Cost answer that is superior in R value and yet doesn’t bankrupt you.

Obviously, the idea would be to have insulation spray all the way through the house and inside the walls if that were necessary but it is usually very expensive to do that even with the help of kits.

Slab Insulation

On the other hand, spray foam will fill in nooks and crannies better than any other product and more than one do it yourselfer has chosen to combine extruded Home Insulation Cost and seal the cracks with a polyurethane spray.

Shop Insulation

This is one of those tricky areas when you and a calculator must sit down and do some hard cost calculations. Expanding foam is superior to almost any other product.

Wall Spray Foam Insulation

Now, your budget will thank you for the energy savings of an expanding foam attic or even wall insulation but it may not be able to support professional installation or even a full kit to cover your home.

Instead, if the math is unfavorable for using foam insulation in a spray form in all the needed areas, then consider using a less expensive alternative along with the expanding foam. Try saving the foam application for areas where it would be of maximum benefit.

Exterior walls may use rigid polyisocyanurate foam covered with aluminum in order to provide exceptional insulation in Texas and still stay within a reasonable budget.

Rigid Foam Board Insulation

Attic Insulation What is Important to Know

Animals love attics and usually damage the attic insulation. To prevent further damage to the insulation, it's wise that you remove the animals as soon as you identify that they are there. To guide you here are ways on how to remove the animals from the attic:


Raccoons are very smart; therefore, it's very difficult to catch and remove them from the attic. To easily catch them you need to know the holes that they use to get into the space.

After identifying the hole you should place a cage trap near the hole. If there are baby raccoons in the attic and you can't find the mother, you should place the babies in a cage trap and use them to draw in the mother. For ideal results you should monitor the babies closely and keep them protected from weather and predators.

The easiest way of removing the squirrels from the attic is finding the holes that they use to get in and out of the attic. You should then set a trap near the hole. You should avoid using poison to control the squirrels. This is to avoid having the powerful smell that comes from a dead squirrel. The best traps to use are lethal and live traps.


In addition to the above animals, other animals that are common in attics are snakes, bats, and opossums. If you are scared of removing the animals, you should highly consider hiring a professional to do the work for you.

The Purpose of Radiant Barrier Insulation

Basement Wall Insulation


I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?


Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles


Duct Tape

Staple Hammer and Staples

Utility Knife


Insulation Blowing Machine (Available at your local rental store)

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.