Ceiling Insulation Installation Richardson

Is it time for Ceiling Insulation Installation in Richardson? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.

Basement Wall Insulation

One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.

Spray On Insulation

When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.

Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.

Almost all Ceiling Insulation Installation in Richardson are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.

High Density Insulation

Will Dry Ice Blasting Solve Attic Mold the Problem?

You've read all of the articles and know all the pro's and con's to the attic insulation called radiant barrier. Now what? You need to ask yourself two vital questions and they are:

1. Does my attic have ductwork?
2. What is the climate conditions in my area (hot, cold?)
3. What are the install methods of radiant barrier and which one should I use?

We're going to start by answering question number 3 first and tell you what the install methods of radiant barrier are.

The two prominent methods of installation are: stapling your reflective insulation to your roof rafters or just laying your reflective insulation over your previous traditional attic insulation. Each method has pro's and con's however, in order to make an informed decision you will need to answer question two.

However, if there is ductwork in the attic you may lean towards stapling the radiant barrier to your attics rafters. According the Department of Energy this is the optimal installation process in order to minimize summer heat gain and winter heat loss in the warmer climates. Though it is up for some debate on which method is better for energy savings.

It doesn't matter which install method you decide on. You will see energy savings with it. The staple-up method results in the minimum overall heat gain into your home. Both of these methods of installing radiant barrier is going to make your home feel more comfy and save you money on your utility bills.

Loose Fill Insulation

How Much Attic Insulation is Enough?

House attic mold is one of the most "popular" items in my property inspection reports. And now is time for an explanation of how to kill mold and / or how to clean mold in the attic. But before I do that, let me give you a little advice, something to consider before you sign a few (if you're lucky) thousand dollars contract agreement with a mold remediation company.

Attic mold remediation TIP - an alternative (to consider):

Let us assume that you are in the middle of a real-estate transaction, and the home inspector just revealed to you, that your entire house attic is contaminated with mold.

If you have a brand new roof, you can only blame yourself or try to blame the roofing contractor for not checking the attic before replacing the roof (he will laugh at you unless you've actually asked the guy to check the attic before the roof replacement). If you have an older roof, the importance of this advice is even greater.

Call at least 2-3 mold remediation companies for an estimate - specify to the representatives, that you not only want to have the mold removed, but also attic ventilation system corrected / installed if necessary / ask if the attic insulation requires replacement.

With the numbers from the mold remediation contractors, call 2-3 roofing contractors, and ask them for a quote on the roof replacement cost including decking boards / plywood (ask the roofer to check the attic area), attic ventilation improvement, and insulation if necessary.

Be cautious if they only suggest humidistat controlled power vent installation - without properly functioning soffit vents or any type of vents along the lower portion of the roof this might not be an adequate solution.

If the attic insulation replacement is not required (it most cases it will not be possible to tell without laboratory testing), make sure it's sealed with plastic foil before the roof and its decking replacement. Fold the foil sealing its contents after the contaminated decking has been removed, and dispose of as a regular waste (EPA recommendation).

I personally wouldn't even attempt to do it myself, so my suggestion is:

Use a professional mold remediation company:

  • check their background and check it manually by calling their clients
  • ask for clients who had their attic mold remediated approximately 1 year ago - it usually takes a winter for the mold to start growing again if the job wasn't fully completed
  • Insist on removing the mold completely instead of encapsulating it (Media Blasting methods give the best results).
  • Encapsulation is simply a process of covering the mold contaminated surface with paint (paint like product) that contains (or at least some of them do) mold killing chemicals

If your attic mold is properly removed and all of the issues responsible for its growth corrected, which is even more important than mold removing, it will not re-grow / no need for encapsulating.

  • Hire a different contractor for mold testing and mold remediation to eliminate conflict of interest.
  • Make sure that you perform an independent clearance test after the mold remediation process completion.
  • Clearance test is to determine if there are any mold spores remaining in the previously contaminated area
Extremely important - examine the attic (or have somebody do it for you) after the mold cleaning procedure is finished.

All wood (framing and decking) surfaces should be perfectly clean (like brand new), unless there was some rotting that resulted from leaking roof or extremely humid conditions in the attic - those sections of wood should be either replaced or reinforced from underneath. You don't want anyone to fall through the roof while servicing it or just inspecting.


Roof Insulation Cost Texas