Is it time for Foam Insulation Cost in Colleyville? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.
One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.
When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.
Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.
Almost all Foam Insulation Cost in Colleyville are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.
Sealing and Insulating Your Attic Hatch
Most of the energy costs spent to keep a home warm in the winter and cool in the summer end up leaving through the attic. In the summer, the sun's heat pours in through the attic and in the winter, warm air rises past the ceiling and out of the home. Saving on energy costs starts in the attic, but how much insulation is enough?
Insulation is rated by number denoting how much of a thermal barrier each type of insulation provides. The farther north one goes the higher insulation number needed. Cold weather states, such as the Atlantic north-east, mountain states, and northern Mid-west require an R-49 rating. Warm weather states in the middle latitudes call for R-40; Southern and Gulf States would require R-38.
These guidelines offer the answer to the question, "how much insulation is enough?"
Adequate home insulation is the best way to keep a home comfortable while saving energy costs. With just a ruler, any homeowner can determine if they are meeting their insulation needs. With many options available to increase the insulation in an attic, no homeowner has to needlessly suffer through a cold winter, hot summer, or high utility bills.
Is Radiant Barrier Worth Adding To Your House?
I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?
Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.
First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.
Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:
Loose Fill Insulation
Staple Hammer and Staples
Insulation Blowing Machine (Available at your local rental store)
I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.
The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.