Roof Insulation Installation Plano

Is it time for Blown Attic Insulation Cost in Plano? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.

Wall Spray Foam Insulation

One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.

Radiant Barrier Insulation

When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.

Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.

Almost all Blown Attic Insulation Cost in Plano are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.

Roll Insulation

Icynene Insulation

Spray Foam Insulation allows residential and commercial structures to be more sustainable by making houses more energy efficient, healthier, and durable than traditionally insulated homes. Most spray foam materials are water assisted and soy-based, so they do not have much of a negative impact on the environment and can provide the homeowner with decreased energy costs in the end.

Most traditional spray foam materials are made of glass or cellulose, which are not that environment friendly. However, spray-on insulation, made of polyurethane foam, is pumped through pressurized spray nozzles. Once sprayed, it expands to one hundred times its original size and provides a thermal seal and it utilizes renewable resources. The product also can be water-blown which means it is more environmental friendly than traditional one. When it expands, it fills each cavity, crevasse and hole to create a sealed envelope. If properly installed, most spray foam does not usually foster mold or insects and does not break down, hence creates a sealed interior, blocking unwanted pollution out. Spray foam insulation adheres to most material, such as wood and steel and can be used for new constructions or renovations. If the installation is correct, this product poses few issues with properly installed electrical wiring.

Being a complicated and messy process, it will be easier and more effective in new construction rather than existing homes. Once installed properly, it takes care of the health, safety and comfort of your house.

Wall Foam Insulation

How to Evaluate the Types and Amount of Insulation

Insulating your attic is a great way to help lower your heating and cooling bills.

Using batts or rolls easily helps you achieve the recommended R-value for better insulating performance.

Ready? Okay, let’s go for it! Use layers of high R-Value insulation like R-30 or 38.

And depending on whether you have some insulation or no insulation, you may need a mix of Kraft-faced and unfaced, but we’ll get to that later.

Here are the tools, supplies and safety gear you’ll need for installation.

Let’s get started.

Insulation comes in rolls or pre-cut batts.

Either works, but we recommend using rolls in your attic to quickly cover a large area.

Just roll out the insulation and cut as needed.

Pre-cut batts are great for areas built at standard dimensions or when it’s easier to move small sections of insulation at a time.

If you’re adding insulation to what’s already there, you need to use unfaced insulation.

Putting Kraft-faced insulation over existing insulation will trap moisture and lead to mold and other problems.

That’s not good.

With existing insulation, all you need to do is add rolls of new unfaced insulation until you reach your desired R-Value.

If you’re insulating an attic that has no existing insulation, you could use Kraft-faced insulation on your first layer because that paper or vapor retarder, will help keep moisture from moving between your home below and the attic.

Before we start insulating the attic from scratch, let’s seal any air leaks with caulk for small gaps and foam for gaps up to three inches.

Then, we need to protect any objects that produce heat, like these can lights, by building a baffle.

A baffle is like a box that you place around the heat source.

You can construct one using cardboard or rigid foam.

This will need to keep insulation at least three inches away from the object.

Ventilation is incredibly important with attic insulation.

Be sure to use a vent chute so the fiberglass doesn’t come into contact with the underside of the roof.

Now that all that’s done, we can get down to it.

Measure your joist cavity opening to make sure your insulation will fit side to side and end to end.

As you cut down your roll, use a 2x4 and a utility knife on top of your base for a clean, easy cut.

If you have a narrow joist opening, you may need to trim it lengthwise before getting into the attic.

When you’re installing in your attic floor, place the paper side down against the floor to help prevent moisture from moving between your home below and the attic.

The unfaced side should be what you see when you’re finished.

Place your insulation between the joists and press it into place, just like you would with a wall.

You can continue to add rolls of unfaced insulation until you reach your desired R-Value.

Don’t forget about the attic door or hatch! Foamboards and weatherstripping can do the trick.

So that’s insulating attics with rolls or pre-cut batts! Want to see other places in your home where you may need to insulate? Check out these helpful videos.


Roof Insulation Cost Texas