Is it time for Spray Foam Installers in Haltom City? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.
One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.
When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.
Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.
Almost all Spray Foam Installers in Haltom City are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.
The History of Spray Foam InsulationReflective foil insulation, or ultra concrete barrier foil (Ultra CBF) are designed and manufactured for use directly under any poured concrete or cement slab. The design features of Ultra CBF are made so that no part of the reflective foil is in contact with the cement itself. It uses a unique laying system that consists of bubbles to ensure there is a dead air space between. The main difference between reflective foil insulation and regular foil insulation is with the regular foil it is made with a –foil/bubble/foil design-, while the reflective foil insulation is made with a patented –bubble/foil/bubble- process. This means that he foil layer of the reflective type is between the layers of the insulation. With traditional methods of insulating under concrete or cement slab use a two step process. First they incorporate a two inch foam panel, then a six mil. Clear plastic vapor barrier is installed. When you choose to use the reflective foil insulation, it has the vapor barrier already built right in, so not only are you saving the time and energy because you eliminate one step, you’re also saving money by using an all in one product. Reflective foil insulation is used for three main reasons, each one being very important in your homes efficiency. It creates a vapor barrier to keep the water from building up and getting into the floor itself. When this happens you’re in for a rather large repair bill. It also insulates the cement slab against the natural earth below. This is the best method to prevent heat loss. Reflective foil insulation also serves to create a radon barrier. Radon is the potentially lethal gases that come up through the ground; you can not smell or see this gas. By using the reflective foil insulation you eliminate the possibilities of this problem arising. The potential saving by using reflective foil insulation are many. By not using this type of insulation for under slab protection, you may be shooting yourself in the foot, in regards to the problems that can develop as mentioned above. Do it right the first time, and you home will be safer and much more energy efficient.
Installing Insulation on a Steel Building
Insulating your attic is a great way to help lower your heating and cooling bills.
Using batts or rolls easily helps you achieve the recommended R-value for better insulating performance.
Ready? Okay, let’s go for it! Use layers of high R-Value insulation like R-30 or 38.
And depending on whether you have some insulation or no insulation, you may need a mix of Kraft-faced and unfaced, but we’ll get to that later.
Here are the tools, supplies and safety gear you’ll need for installation.
Let’s get started.
Insulation comes in rolls or pre-cut batts.
Either works, but we recommend using rolls in your attic to quickly cover a large area.
Just roll out the insulation and cut as needed.
Pre-cut batts are great for areas built at standard dimensions or when it’s easier to move small sections of insulation at a time.
If you’re adding insulation to what’s already there, you need to use unfaced insulation.
Putting Kraft-faced insulation over existing insulation will trap moisture and lead to mold and other problems.
That’s not good.
With existing insulation, all you need to do is add rolls of new unfaced insulation until you reach your desired R-Value.
If you’re insulating an attic that has no existing insulation, you could use Kraft-faced insulation on your first layer because that paper or vapor retarder, will help keep moisture from moving between your home below and the attic.
Before we start insulating the attic from scratch, let’s seal any air leaks with caulk for small gaps and foam for gaps up to three inches.
Then, we need to protect any objects that produce heat, like these can lights, by building a baffle.
A baffle is like a box that you place around the heat source.
You can construct one using cardboard or rigid foam.
This will need to keep insulation at least three inches away from the object.
Ventilation is incredibly important with attic insulation.
Be sure to use a vent chute so the fiberglass doesn’t come into contact with the underside of the roof.
Now that all that’s done, we can get down to it.
Measure your joist cavity opening to make sure your insulation will fit side to side and end to end.
As you cut down your roll, use a 2x4 and a utility knife on top of your base for a clean, easy cut.
If you have a narrow joist opening, you may need to trim it lengthwise before getting into the attic.
When you’re installing in your attic floor, place the paper side down against the floor to help prevent moisture from moving between your home below and the attic.
The unfaced side should be what you see when you’re finished.
Place your insulation between the joists and press it into place, just like you would with a wall.
You can continue to add rolls of unfaced insulation until you reach your desired R-Value.
Don’t forget about the attic door or hatch! Foamboards and weatherstripping can do the trick.
So that’s insulating attics with rolls or pre-cut batts! Want to see other places in your home where you may need to insulate? Check out these helpful videos.