Is it time for Cost Attic Insulation in Burleson? What is the best type to choose? Let us focus on four specific types. One is blown attic insulation the other is batt insulation. Each type has pros and cons. However, which is the best choice for you.
One of the best advantages of blown attic insulation over batt is that the blown style covers everything; while there can be open areas in the batt type.
When you’re looking to have your home or building insulated with spray foam insulation, you have a couple of product choices. Whether you go with closed foam or open foam insulation, the differences in their make will make a big difference in which one will work best for your needs.
Radiant barrier insulation has one reflective side that is made from an aluminum coating. Any radiant barrier insulation can be installed in an existing or new home. The reflective side of the barrier insulation is made to face the open air pocket of the surface.
Almost all Cost Attic Insulation in Burleson are tested and rated as fireproof. If for some strange reason you find one that is not, stay away from that product.
The Cost of Spray Foam Insulation
Adding insulation to your attic is a great way to save energy, but there are a number of choices that you need to sort through. What is the best type for your situation? What is the best location for this added insulation? How much should you add?
The first thing that you need to determine is how much insulation you already have. Measure the depth and determine the type. Then multiply the depth by the appropriate value: Cellulose: 3.1, Fiberglass Batt or Blown: 3.7, Closed-Cell Foam: 6.2, Open-Cell Foam: 3.6.
Before you move any further to insulate your attic, you should make sure that you have any knob and tube wiring in your attic that would be covered by insulation replaced. The wires in this type of system need to be in the open air in order to dissipate heat. If they are surrounded by insulation this will trap the heat and cause a fire hazard.
Once you have calculated the R-value of your insulation, you need to determine how much more you should add. Energy Starr has developed recommended levels of attic insulation for every Zone throughout the US. See map at Energy Star and chart below. However, what it boils down to is most houses don't have enough insulation. R-30 is the bare minimum and unless you live in south Florida, the recommended amount is twice that.
Radiant Barriers: work differently than thermal insulation. They reflect the heat away from the thermal insulation, instead of slowing the heat transfer through it. This effectively increases the performance of your thermal insulation in your attic by 50% to 70%. Radiant barriers work best if they are installed between the attic insulation and the roof sheathing, and when they are sloped so that dust will not accumulate on it as quickly. Furthermore, radiant barriers are fairly inexpensive and easy to install.
Your last step is to determine if you are going to add thermal insulation, a radiant barrier, or both. If your house already has what is the code minimum in many locations of R-30, adding a radiant barrier should boost its effectiveness to 45 or even 50. Or if you have an old house with 5 ½" of fiberglass or cellulose (R-17 to R-20) and you add another R-19 and a radiant barrier, you effective insulation value should be between 54 and 65.
Wall Foam Insulation
I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?
Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.
First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.
Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:
Loose Fill Insulation
Staple Hammer and Staples
Insulation Blowing Machine (Available at your local rental store)
I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.
The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.